SL2

Overview

SL2 is a completely corrosion resistant linear guide featuring ground stainless steel slides and linear motion bearings. SL2 carriages are made from strong, yet light-weight aluminum alloy. SL2 slides may also be mounted to GV3 beams for further design versatility.

Slide lengths up to 4 meters from a single piece
Clean room compatible
Available as assembled units or as components
Plastic plugs can be added to eliminate dirt traps

Assembled Systems

Three aluminum carriage lengths are available to meet size needs as well as moment loading conditions. Carriage units come assembled or as a kit for on-site assembly with your choice of lubricators. Two stainless steel V bearing types allow for a choice between highly compliant twin bearings and double row bearings for higher load demanding applications.

Stainless Steel Spacer and Flat Slides

Slides are made of stainless steel AISI 420 series and are ground to a N5 rating. V slides are available in the following configurations:

Double edge spacer slide
Double edge flat slide

Mounting holes are available as counterbores or through-bores. Dowel pins can be used to more accurately align track during installation.

Cap Seals and Lubricators

Cap seals and lubricators allow for optimal performance of systems by properly lubricating the interface between the V slide and V bearing. Both cap seals and lubricators provide a grease reservoir for continuous lubrication during system life.

Alumium Carriage Plates

Aluminum carriages come in three standard lengths. Carriages are coated with an anti-corrosive coating, which is approved by the US Department of Agriculture. Hole patterns on standard carriages readily accommodate cap seals and lubricators. Custom carriages can also be made from customer specified materials such as stainless steel.

CarriageType	Dry System, Twin & DR Type Bearing
	L1(max)	L2(max)	Ms(max)	Mv(max)	M(max)
	N	N	Nm	Nm	Nm
SSCPMS12	80	80	0.4	40 x Y	40 x Y
SSCPS25	320	320	3.6	160 x Y	160 x Y
SSCPS35	320	320	5	160 x Y	160 x Y
SSCPS50	320	320	7.3	160 x Y	160 x Y
SSCPM44	640	640	13	320 x Y	320 x Y
SSCPM60	640	640	18	320 x Y	320 x Y
SSCPM76	640	640	23	320 x Y	320 x Y
SSCPL76	1440	1440	50	720 x Y	720 x Y

CarriageType	Lubricated System, Twin Type Bearing
	L1(max)	L2(max)	Ms(max)	Mv(max)	M(max)
	N	N	Nm	Nm	Nm
SSCPMS12	240	240	1.3	120 x Y	120 x Y
SSCPS25	960	960	11	480 x Y	480 x Y
SSCPS35	960	960	15	480 x Y	480 x Y
SSCPS50	960	960	22	480 x Y	480 x Y
SSCPM44	3000	3000	60	1500 x Y	1500 x Y
SSCPM60	3000	3000	84	1500 x Y	1500 x Y
SSCPM76	3000	3000	108	1500 x Y	1500 x Y
SSCPL76	6000	6000	210	3000 x Y	3000 x Y

CarriageType	Lubricated System, DR Type Bearing
	L1(max)	L2(max)	Ms(max)	Mv(max)	M(max)
	N	N	Nm	Nm	Nm
SSCPMS12	Not Applicable
SSCPS25	1600	3000	17	1500 x Y	800 x Y
SSCPS35	1600	3000	25	1500 x Y	800 x Y
SSCPS50	1600	3000	37	1500 x Y	800 x Y
SSCPM44	3600	6000	72	3000 x Y	1800 x Y
SSCPM60	3600	6000	100	3000 x Y	1800 x Y
SSCPM76	3600	6000	129	3000 x Y	1800 x Y
SSCPL76	8000	10000	280	5000 x Y	4000 x Y

Technical Specifications

Stainless Steel Roller Bearing Assemblies

Stainless steel twin roller bearing type is a two piece deep groove ball bearing, which provides the most compliance and tolerates the highest amount of misalignment.

Stainless double row roller bearing type utilizes a one piece bearing design with a double row ball configuration for higher load capacity and rigidity.

Nitrile seals are standard for stainless steel twin and double row bearings to provide greater protection from liquid and small particle debris. Through-hole and blind hole mounting type configurations are also available in two lengths to handle different carriage thicknesses.

Flange Clamps

Flange clamps allow for mounting of stainless steel slides at the ends. Aluminum alloy is used to make the flange clamps, which are then coated with an anti-corrosive coating. The anti-corrosive coating is approved by the US Department of Agriculture.